2008 Kawasaki Ninja 250r Manual Pdf

This will burn out the diodes in the electrical parts. This digit in the frame number changes from one machine to another. If the clearance is out of the specified range, use the additional shim.

Set it close to the bottom of the cylinder, where cylinder wear is low. If they do not, adjust the chain slack and align the wheel alignment see Drive Chain Slack Adjustment.

Precautions Newly activated sealed batteries require an initial charge. Guide Run the left switch housing lead through into the guide. Therefore the cutter must not be used for other purposes than seat repair. Do not use fluid from a container that has been left unsealed or that has been open for a long time. If the gap is too wide, the clutch may not release fully.

If the shock absorber does not smoothly stroke or noise is found, inspect the oil leak see Rear Shock Absorber Oil Leak Inspection. Illustrations and photographs in this publication are intended for reference use only and may not depict actual model component parts. If the wheel stops of its own accord in various positions, it is well balanced. Do not use bulb rated for greater wattage then the specified value. Replace the caliper if the cylinder and piston are badly scores or rusty.

Kawasaki Ninja Owners Manuals

Repair methods may vary slightly from make to make. If there is any damage to the frame, replace it. Run the clutch cable and over flow hose into the hole of the reserver tank. Apply molybdenum disulfide grease.

If there is no vacuum pulsation, check the hose line for leak. Run the reserve tank overflow hose into the guides. Guide Run the headlight high lead through into the guide.

Install the hose so that its white mark side faces the radiator. Such a shock to the water temperature sensor can damage it. These names must be the same.

Download Kawasaki Ninja R EXJ8F Repair Manual PDF

Download the right manuals Keep Your Vehicle Running Smoothly

Guide Run the right switch housing lead through into the guide. Install the vaccum switch valve hose so that its white mark faces the air cleaner box.

Such a shock to the unit can damage it. If the tester does not read as specified, replace the coil. The rings should fit perfectly parallel to groove surfaces.

2008 Kawasaki Ninja 250R Owner s Manual

If there is visible damage, replace the sleeve with a new one. Install the clamps as shown, noting their clip direction. Page Newly activated sealed batteries require an initial charge. Band Hold the headlight high lead and insert the band into the upper fairing bracket. Install the hose so that its white paint mark side faces the radiator.

If not, replace the piston and all the piston rings. Increasing the float height lowers the fuel level and decreasing the float height raises the fuel level. The thermostat is a wax pellet type which opens or closes with coolant temperature changes. The fan may start even if the ignition switch is off.

Zip code or city state

If the frame is bent, dented, cracked, or warped, replace it. Be sure to use the dedicated electrolyte container for correct electrolyte volume. Wait until the muffler cool down.

Special tools, gauges, and Indicates a procedural step or work to be testers that are necessary when servicing done. If the intake vacuum difference between the two cylinders exceeds the limit, adjust the synchronization. Lubricate with Rust Inhibitor. Run the clutch cable and reserve tank hose into the hole of the reserve tank. Pull the bulb out to prevent damage to the bulb.

For these reasons, Kawasaki does not recommend temporary exter- nal repair. Lubri- cation points are called out throughout this manual, apply the specific oil or grease as specified. How To Use This Manual Be alert for problems and non-scheduled ticular interest for more efficient and con- maintenance. If the surface is corroded or if the blades are damaged, replace the water pump unit. If the connector is corroded or dirty, libro de los nombres para bebes pdf clean it carefully.

They must be smooth and clean for the radiator cap to function properly. Do not drop or shock the valve seat cutter, or the dia- mond particles may fall off. If the relay does not work as specified, the relay is defec- tive. Observe all the rules listed below. Learn and ob- serve all the rules below.

Racing news

If they show any damage, replace the dust seals with new ones. If the fuel tap screens have any breaks or are deterio- rated, they may allow dirt to reach the carburetor, causing poor running.

If it is damaged, replace it. Such a shock to the relay box can damage it. Be sure to maintain proper alignment and use smooth movements when installing. The difference between the highest and the lowest gauge readings is the amount of backlash.